How to Use Cushion Grip Denture Adhesive.

Cushion Grip is very much different from creams and pastes. It is a soft, pliable material that must be softened in hot water (not boiling) before application.

Heat-Activated: Softens with heat for easy application; sets as it cools for a long-lasting, secure fit

Glue-Free Formula: Sticks only to dentures; mess-free compared to denture creams and pastes

Do Not Use For: Not for broken or extremely ill-fitting dentures; won’t stick to silicone, or metal dentures

How to Apply Cushion Grip

Follow the steps below to apply Cushion Grip. For more tips and tricks, visit us on YouTube @MyCushionGrip.  

WARM THE TUBE

Cushion Grip is a thermoplastic denture adhesive that softens and becomes pliable when heated, making it easier to dispense.

1. Keep the cap on and place the tube cap-side down in a cup.
2. Add hot tap water (not boiling) and let the tube warm for 5 minutes.
3. Check the tube. Cushion Grip should be soft and easy to dispense.

Note: If dispensing remains difficult, warm the tube in the water for a few more minutes.

DISPENSE & ROLL

Once Cushion Grip is soft and pliable:

1. Attach the enclosed slotted key to the end of the tube.
   
2. Turn the key to dispense a ball of Cushion Grip about the size of a dime or 3/4 inch in diameter per denture plate.

Tip: The amount needed depends on how loose your dentures are. Start with a smaller amount and add more if necessary.

APPLY TO LOWER DENTURE FIRST

If you have upper and lower dentures, start with the lower. Otherwise, go to the next step and begin with the upper denture

Make sure your hands and lower denture are clean and completely dry before applying Cushion Grip.  Also, perform this step while wearing your upper denture, but without applying Cushion Grip to it yet.  

1. Begin by rolling Cushion Grip between your palms to form a thin strip.
2. Gently place the thin strip of Cushion Grip along the gum groove from one end to the other. Spread it into a thin, even layer over the required area and press it firmly into place.
3. Let Cushion Grip set for 5 minutes. This allows the material to begin firming up and taking shape before you insert the denture into your mouth.
4. After letting Cushion Grip set, insert your lower denture with your upper denture in place. Bite down firmly for 30 seconds to 1 minute to secure the fit.
   

Tip: Apply Cushion Grip in small amounts and near the gum groove, and add more as needed.

APPLY TO UPPER DENTURE

If you have both upper and lower dentures, repeat the same procedure for your upper denture.

Make sure your hands and upper denture are clean and completely dry before applying Cushion Grip. Perform this step while wearing your lower denture.

1. Begin by rolling Cushion Grip between your palms to form a thin strip.
2. Gently place the thin strip of Cushion Grip along the gum groove from one end to the other. Spread it into a thin, even layer over the required area and press it firmly into place.
3. Let Cushion Grip set for 5 minutes. This allows the material to begin firming up and taking shape before you insert the denture into your mouth.
4. Insert the upper denture and press it firmly against your front gums. Use your thumb to press upward against the roof of your mouth, then bite down firmly for 30 seconds to 1 minute to create a secure suction seal.  

Tip: Start with a small amount of Cushion Grip in the gum groove and add more as needed. 

Note: During application, mild tingling may occur, similar to mouthwash, for a few minutes due to the small amount of alcohol; letting it sit 10 minutes before inserting can reduce this.  

SET & CURE THE CUSHION GRIP

Continue wearing your dentures for 2 to 6 hours to allow Cushion Grip to fully set and cure. The longer you keep your dentures in place, the better Cushion Grip will set.

Avoid removing your dentures, eating, or drinking for the first 2 hours. After 2 hours, you may sip liquids, but avoid holding liquids in your mouth or drinking anything hot.

For the first 24 hours, do not soak your dentures or use other denture adhesives. After 24 hours, you can clean and soak your dentures as usual and use other denture adhesives or powders if needed. Cushion Grip is waterproof and will not wash away or break down in water.

How to Remove Cushion Grip

If you feel the need for a stronger seal after a few days, or it's time for a new application, remove the old Cushion Grip and apply a fresh coat. It's recommended to replace Cushion Grip on your dentures at least once a week for optimal fit.

Helpful Video Tutorials

• How to Dispense Cushion Grip More Easily
• How to Apply Cushion Grip to Dentures
• Dealing with Excess Spillage
• Benefits of Applying Cushion Grip Before Bed
• How to Remove Cushion Grip from Dentures

Still Have Questions About Using Cushion Grip?